LP8556SQX-E08/NOPB

Texas Instruments
595-LP8556SQX-E08NPB
LP8556SQX-E08/NOPB

メーカ:

詳細:
LED照明ドライバIC 6Ch Hi-Eff/Efficacy LED Backlight Drvr A A 595-LP8556SQE-E08NPB

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 3,598

在庫:
3,598 すぐに出荷可能
工場リードタイム:
6 週間 表示されている時間を超える工場生産予定時間。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(4500の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥191.2 ¥191
¥138.3 ¥1,383
¥125.1 ¥3,128
¥110.8 ¥11,080
¥103.8 ¥25,950
¥99.5 ¥49,750
¥96.2 ¥96,200
¥90.7 ¥226,750
完全リール(4500の倍数で注文)
¥88.6 ¥398,700
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

他のパッケージ

メーカ 部品番号:
梱包:
Reel, Cut Tape, MouseReel
在庫状況:
在庫
価格:
¥436
最低:
1

製品属性 属性値 属性の選択
Texas Instruments
製品カテゴリー: LED照明ドライバIC
RoHS:  
6 Output
Boost
23 mA
WQFN-24
20 V
2.7 V
312 kHz, 625 kHz, 1.25 MHz
16 V to 34.5 V
LP8556
- 30 C
+ 85 C
Adjustable Switch Frequency, Enable/Shutdown, I2C Control, PWM Control
Reel
Cut Tape
MouseReel
ブランド: Texas Instruments
組立国: Not Available
拡散国: Not Available
原産国: MY
入力電圧: 2.7 V to 20 V
取り付け様式: SMD/SMT
チャンネル数: 6 Channel
製品タイプ: LED Lighting Drivers
工場パックの数量: 4500
サブカテゴリ: Driver ICs
供給電流 - 最大: 3.65 mA
単位重量: 38.700 mg
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

この機能はJavaScriptを有効にすることが必要です。

JPHTS:
854239099
CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
TARIC:
8542399000
MXHTS:
8542399901
ECCN:
EAR99

IS32LT3175N/P Single-Channel Linear LED Drivers

ISSI IS32LT3175N/P Single-Channel Linear LED Drivers come with fade in/out and PWM dimming. The regulators serve as a stand-alone LED driver-configurable from 20mA to 150mA with external resistors, no microcontroller is necessary. A logic level “courtesy light” signal from the PWM pin can be interfaced to precisely drive the LED channel. The IS32LT3175P obtains a positive polarity PWM signal. In addition, the IS32LT3175N obtains a negative polarity PWM signal. The regulator integrates a 63-step fade-in and fades out the algorithm (Gamma correction). This causes the output LED current to increasingly rise up to the full source value after the EN pin is pulsed.