TLV627432YFPR

Texas Instruments
595-TLV627432YFPR
TLV627432YFPR

メーカ:

詳細:
スイッチング電圧レギュレータ 2.15-V to 5.5-V 400 -mA high efficiency

ECADモデル:
無料のライブラリローダーをダウンロードし、お使いのECADツール用にこのファイルを変換してください。ECADモデルの詳細について

在庫: 4,351

在庫:
4,351 すぐに出荷可能
工場リードタイム:
12 週間 表示されている時間を超える工場生産予定時間。
最小: 1   倍数: 1
ユニット価格:
¥-
合計 額:
¥-
EST関税:
パッケージング:
完全リール(3000の倍数で注文)

価格 (JPY)

数量 ユニット価格
合計 額
カットテープ/ MouseReel™
¥128 ¥128
¥91.6 ¥916
¥82.5 ¥2,063
¥77.4 ¥7,740
¥75.2 ¥18,800
¥64.6 ¥32,300
¥62.3 ¥62,300
完全リール(3000の倍数で注文)
¥59.3 ¥177,900
¥57.7 ¥346,200
† ¥750 MouseReel™の料金が追加され、ショッピングカートに加算されます。すべてのMouseReel™の注文は、キャンセルおよび返品できません。

製品属性 属性値 属性の選択
Texas Instruments
製品カテゴリー: スイッチング電圧レギュレータ
RoHS:  
SMD/SMT
DSBGA-8
Buck
1.2 V to 3.3 V
400 mA
1 Output
2.15 V
5.5 V
460 nA
1.2 MHz
- 40 C
+ 85 C
TLV627432
Reel
Cut Tape
MouseReel
ブランド: Texas Instruments
組立国: Not Available
拡散国: Not Available
原産国: PH
入力電圧: 2.15 V to 5.5 V
負荷調節: 0.001 %/mA
製品タイプ: Switching Voltage Regulators
シャットダウン: No Shutdown
工場パックの数量: 3000
サブカテゴリ: PMIC - Power Management ICs
供給電圧 - 最小: 2.15 V
タイプ: High Efficiency
単位重量: 1.500 mg
製品が見つかりました:
類似製品を表示するには、チェックボックスを1つ以上選択します
このカテゴリーの類似製品を表示するには、上記のチェックボックスを1つ以上選択してください。
選択した属性: 0

この機能はJavaScriptを有効にすることが必要です。

CNHTS:
8542399000
USHTS:
8542390090
ECCN:
EAR99

TLV627432 High-Efficiency Buck Converter

Texas Instruments TLV627432 High-Efficiency Buck Converter is a step-down converter with a typical ultra-low quiescent current of 360nA. The device is optimized to operate with a 2.2µH inductor and a 10µF output capacitor. The TLV627432 uses DCS-Control™ and operates with a typical switching frequency of 1.2MHz. In Power Save Mode, the device extends the light load efficiency down to a load current range of 10µA and below. TLV627432 provides an output current of 300mA. The TLV627432 provides 8 programmable output voltages between 1.2V and 3.3V, which is selectable by three selection pins. The TLV627432 is optimized to provide a low output voltage ripple and low noise using a small output capacitor. Once the input voltage comes close to the output voltage, the device enters the No Ripple 100% mode to prevent an increase of output ripple voltage. In this operation mode, the device stops switching and turns the high side MOSFET switch on.